Showing results: 121 - 135 of 353 items found.
-
ADCFN04 – HPC -
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN04 is a four channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides DC coupled single-end analog input and digital output with DC-250KHz sampling speed based on Linear Technology’s LTC2376-16. The output is 16-bit data and it can be obtained through SPI interface on LTC2376-16 from the FPGA on the FMC carrier board. One trigger input is provided for capture control.
-
MSXB 085 -
Microstar Laboratories, Inc.
The MSXB 085 Isolated Analog Expansion Board provides isolated analog inputs and isolated analog outputs for DAP systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing skew.
-
Datexel
The EPL101 PLC is a circuit board OEM PLC. The EPL101 has 4 analog inputs, 7 digital inputs and 2 inputs for Encoders. It has 6 relay outputs, 5 that are rated for 5 Amps and 1 relay rated for 16 Amps. It also has an analog output 0-5 Volts. The outputs can be simple on off or P, PI,PID or PD control. The EPL101 accepts inputs from K, S, T, R, J or E type thermocouples, Pt100, Ni100 RTD'S. NTC10K thermistor inputs. The EPL101 also accepts inputs from sensors with 4-20mA, 0-20mA, 0-20mV or 0-1V signal. It also has 6 digital PNP inputs up to 1 Hz and 2 NPN inputs up to 2 K Hz.
-
SE-1620 -
Ono Sokki
The SE-1620 is an engine tachometer that performs measurement of the number of revolutions of a gasoline engine by connecting an engine revolution sensor such as an ignition pulse detector. A 100-mm wide-angle meter is used for the display, and both analog output and pulse output functions are provided as standard.Simply attach an ignition pulse detector or one of our other compatible detectors to the engine to enable measurement of the number of revolutions of a gasoline engine. The inputs, outputs and input power supply are all isolated to ensure the output of analog and pulse signals with superior noise resistance and stability characteristics.
-
2246 -
Sensoray Co., Inc
Video overlay up to full screen at up to 1920x1080 SDI (HD/SD) and analog inputs DVI, SDI (HD/SD), and analog outputs Prescaled SD A/V compression engine with MPEG-1/2/4 output Up/downscaling on DVI and analog outputs Captures uncompressed HD/SD frames Generates "freeze frame" video from captured frames Video "zoom" on MPEG stream and DVI output Isolated general-purpose digital I/O: 8 in / 4 out USB 2.0 interface
-
Datexel
The Datexel range of Modbus RTU analog input cards for both RS485 and RS232 with Modbus or ASCII protocol can be combined with the DAT9000 series of Modbus Masters. A choice of input cards or modules are available and have various optional inputs such as Voltage, Current, Thermocouples, RTD, and Resistance. Also a choice of 2, 4, 8 channel options are available. The DAT3011 is a Modbus RTU Slave with 1 selectable universal input (Thermocouples, RTD, mV, RTD's or Resistance), 2 x 4-20mA or 0-10V input and 2 x4-20mA outputs. The DAT3011 also has 3 digital inputs and 3 relay outputs. Each module is isolated from each other and is set up using the DAT3000 software Development package which is free of charge from the Datexel download web page. Datexel also has universal input modules. An 8 channel analog input card is available making the DAT3000 series a very economical solution to large and small scale Data Acquisition. Combining these analog input cards with the analog output cards, the digital input/output cards and the communication devices make Datexel the smart choice where Data Acquisition is required.
-
APCI-3501-8-2P -
TEAM SOLUTIONS, INC.
*"-2P" indicates custom version*8 analog output channels, 14-bit*Optical isolation 500 V*4 digital Input*4 digital output*24 V, optically isolated*Watchdog
-
GE-1400 -
Ono Sokki
Handheld type digital engine tachometer to be designed for dedicated r/min measurement of 4-cycle diesel engines. R/min direct reading measurement is available only by clamping a CP-044 Diesel Engine Rotation Sensor (sold separately) to a fuel injection pipe.Both analog (switchable between analog and monitor output) and pulse outputs are provided; enabling to use analog output for data recording (monitor output for sensor waveform checking or analysis input signal of FFT analyzer), and to use pulse output for tracking analysis signal of FFT analyzer.
-
DAT3100 Series -
Datexel
The Datexel DAT3100 series is a range of Modbus digital input output modules. These cards or modules have the ability to accept digital voltage inputs and provide an output by the way of relays, NPN or PNP transistors. The DAT3100 devices can communicate with RS485 or RS232 on a Modbus or ASCII protocol making the DAT3100 series a very economical solution to large and small scale Data Acquisition. Combining these digital input output devices with the DAT9000 controllers and the DAT3000 analog input output modules make Datexel the smart choice where Data Acquisition is needed.
-
DAT4540R -
Datexel
The Frequency to Current converter DAT4540R is a signal conditioning din rail mount converter which converts a pulse input to an analog output equal to the set range which is selectable from 0.1 Hz up to 20 KHz. The DAT4540R also provides 2 relay outputs and a transistor output. The input can be from a Tacho, TTL, PNP transistor or from any Namur standard. The DAT4540R provides a Voltage or Current output that is isolated from the power supply and input.
-
VME-6500 6U -
Abaco Systems Inc
The VME-6500 is a 6U VME Multifunction I/O board that can deliver in a single chassis slot the analog and digital I/O capabilities that could previously have occupied four slots, and can therefore make a significant contribution to substantially enhance performance and functional density. A high density and versatile design it provides 8 analog inputs and outputs as well as 16 digital inputs and outputs, all in a single 6U double Euro form factor.
-
DACNF04 – HPC -
Sundance Multiprocessor Technology Ltd.
The RFM-DACNF04 is a four channel Digital to Analog converter FMC which complies with VITA 57.1-2010. Each channel provides 16-bit input and one DC coupled single-end analog output with DC – 250KHz sampling speed based on Linear Technology’s LTC2704-16. The 16-bit input data for each channel is provided through SPI from the FPGA on the FMC carrier board. A single-ended TTL level trigger output is provided from the FPGA.
-
PAD64 -
Ponovo Power Co., Ltd.
PAD64 DIO(digital input/output)-AIO(analog input/output) Converter is the equipment which could be used for DI/DO (Digital input/Digital output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and any other equipment which need AIO (analog binary input/ output, dry contacts).
-
Ivium Technologies B.V.
The Peripheral Level Transformer (PLT) is an adapter module that increases the voltage of the analog inputs&outputs for easy communication with external devices. It is connected between the instrument and the periphery.
-
Analog Devices Inc.
Differential amplifiers allow the process of single-ended input to complementary differential outputs or differential inputs to differential outputs. These amplifiers feature two separate feedback loops to control the differential and common-mode output voltages. Analog Devices fully differential amplifiers are configured with a VOCM pin, which can be easily adjusted for setting output common-mode voltage. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single ended output.
